How To Add A Handrail To Garage Steps

How To Add A Handrail To Garage Steps

How To Add A Handrail To Garage Steps

Adding a railing to the garage stairs is a simple job that needs some carpentry skill, but it adds value to the property while giving your garage a more polished appearance. Install a handrail by attaching it to the wall studs near the steps.

Step 1.

Using a stud finder, locate the studs in the wall near the garage stairs and note their places with a pencil. This is where the brackets will be installed to guarantee optimum stability.

Step 2:

Stand at the bottom of the steps and stretch towards the railing, marking its height with a pencil.

Step 1:

Stand at the bottom of the steps and stretch towards the railing, marking its height with a pencil.

Step 2:

Using a measuring tape, measure the distance from the floor to the location you marked on the wall in Step 2. This is one of the locations where a bracket will be installed.

Step 3:

Measure the wall from the steps in two or three places as you move up the stairs, aligning them with the stud markings you established in Step 1. This specifies the location of your extra brackets.

Step 4:

Screw the brackets to the wall with an electric drill. For a secure fit, at least three brackets are required, and more can be used for further security.

Step 5:

Determine how far you want the handrail to extend from the bottom of the steps to the top.

Step 6:

Using a bandsaw, cut a handrail that matches the measurement you obtained in Step 6.

Step 7:

Using a bandsaw, bevel both ends to a 45-degree angle for a polished look.

Step 8:

If required, paint or stain your railing. Some railings are stained and painted already.

Step 9:

Attach the railings to the brackets using screws and an electric drill.

How Do You Remove Concrete Stairs?

You’ve outgrown those last-century concrete steps. Though you may be tempted to take a stick of dynamite and blow up your old concrete steps, there is a far easier and safer way.

Forget about the bombs. Get some safety goggles, work gloves, and an eight-pound sledge hammer.

Your project will not only improve the appearance of your home, but it will also provide you with a stress-relieving workout.

  • Use the 7-inch circular saw to score the steps. Cut through the cement while wearing gloves, eye protection, and a dust mask. Make a weak part with the saw for the sledgehammer to remove.
  • Using the 8-pound sledgehammer, strike the scored part. To swing the sledgehammer with force, channel your inner carnival bell ringer. Prepare to pound the concrete multiple times before breaking a portion of the stairs away.
  • Drill many holes along the edge of the step to form a break-away piece. The hammer drill with a chisel bit will assist you in creating weak pieces of concrete that can be removed with the 8-pound sledge hammer. To remove the concrete pieces, several swings will be required.
  • Use the circular saw to cut through the rebar. Steel-reinforced bars may or may not be present in concrete stairs. These structural bars will be revealed as concrete is removed from the job site.
  • Using the cold chisel and small sledgehammer, remove tiny bits of concrete at the structure’s base. Steps are almost never made of the same concrete as the base.

When you finish your project, you can find a bit of mortar that was used to link the stairs to the main structure that needs to be removed with a little more accuracy.

How Do You Estimate Concrete Steps?

Knowing how much concrete you’ll need before starting a concrete job is critical. Calculating your concrete will differ depending on the sort of job you’re working on.

For example, the amount of concrete required for a driveway will be much different than the amount required for stairs.

Visualizing the space the concrete will take up in terms of rectangles is useful. To measure stairs, for example, divide them into rectangles and determine the volume of each individual rectangle.

The volume is calculated by multiplying the length, breadth, and depth. When you’re done, sum together the rectangle volumes to get the overall volume.

Related Posts

error: Content is protected !!
0

Compare