Samsung Dishwasher Troubleshooting | Samsung Dishwasher Error Code 9E Code

Samsung Dishwasher Troubleshooting | Samsung Dishwasher Error Code OE Code

Samsung Dishwasher Troubleshooting : Samsung Dishwasher Error Codes

A dishwasher error indicates a problem. Here is a referencing to assist you in determining the nature of the issue and the necessary procedures.

Certain issues can be addressed on your own with some basic troubleshooting, restoring normal operation to your dishwasher.

 Samsung Dishwasher Error Code 3C Code

Error Code 3C (Pump operation error) is provided by the manufacturer to indicate that when the drain pump is functioning, it is not experiencing the expected back pressure. 3C basically means the pump has failed.

This is typically a sign of a water leak in the drain system. Conduct a visual inspection of all hoses and connections. Check behind the dishwasher for any significant leaks.

How do I fix my Samsung dishwasher with 3C error code?

To fix the 3C error code, turn off the dishwasher, and then try to start the cycle again. If the error still occurs.

Samsung Dishwasher Error Code 3E Code (High Temperature Water Supply Error)

The 3E error code on Samsung dishwashers is due to high temperature water supply error being abnormally high inside the machine, this is caused by a blocked water system.

To fix the 3E error code due to water being too hot, Verify the hot water supply is not set above 176 degrees Fahrenheit.

Samsung Dishwasher Error Code LC Code

What Does the Error Code LC Mean?

When the LC code on your Samsung dishwasher flashes, this means that the unit’s leak sensor has detected moisture or a leak. To simply clear the code, you can do so by unplugging the dishwater’s power cord for around 15 minutes.

How do I fix my Samsung dishwasher with LC error code?

The LC indicator light on your Samsung dishwasher shows that the dishwasher’s leak sensor has detected a water leak or dampness.

Simply turn off the dishwasher for 15 minutes to clear the error code LC. This should clear the error code and reset the dishwasher.

Samsung Dishwasher Error Code OE Code

What does the error code “OE error” mean?

It is an over-level water error. Error code Samsung dishwasher OE indicates that the dishwasher’s water level has been exceeded. There are various possible explanations for this failure.

It occurs as a result of over spilled water often when the machine is filled with water. If there is this problem in the dishwasher, the discharge will not work and the self-diagnostics system will display an OE error code on the screen.

Again, the 1E and/or the OE Error Code is can be caused by blockage preventing the unit from draining properly.

How do I fix the OE error on my Samsung dishwasher?

Fortunately, most of the time, this can be handled by maintaining the proper water level in the dishwasher and cleaning the Fine Filter System and Sump. If this does not resolve the issue, servicing is unfortunately required.

A clogged discharge system can be detected therefore creates OE error. Allow the dishwasher to cool if it was just turned off.

After that, open the door and locate the grid in the body’s lower portion. CCW the filter knob. Discard the lid and the flat microfilter.

Brush away the dirt and clean the area with flowing water. Examine the bottom. Examine the discharge tube’s condition.

If the quick mode is frequently utilized, it will become blocked with grease. Replace the grid and the filter cover.

If this does not resolve the issue and the system continues to display the OE error number, the water discharge hose may be the source of the problem.

Samsung Dishwasher Error Code 4C /4E Code

The 4E (4C) error code indicates that a problem with the water supply has been detected by the washing machine. The most frequently seen cause of this problem is a clogged or kinked water supply hose.

How do I fix my dishwasher error 4C or 4E Error Codes?

4C, 4E are Water supply error codes meaning the dishwasher is not getting water at the pressure or temperature that it needs. To fix, follow the following steps;

• Verify that the water pressure and temperature satisfy the standards for water supply.
• Floodsafe hoses are incompatible and should not be used with Samsung dishwashers.
• Ascertain that the water supply is working.

Samsung Dishwasher Error Code 5C, SC, 5E, SE Code (Drain Error)

What does the 5E, 5C, SC, SE error code mean on a Samsung washing machine?

When your Samsung washer is in the process of draining and the 5E or 5C, SC, SE error number appears on the display, it indicates that the water is not draining properly from the washer.

Something in the washer may be stuck, jammed, or obstructed, preventing water from draining out.

How do I clear the 5C, SC, 5E, SE error code (Low water level error) on my Samsung dishwasher?

As mentioned above error code 5C, SC, 5E, SE indicates the dishwasher can’t drain. To fix the problem, follow the simple steps below;

• Inspect the drain connection for the dishwasher at the sink.
• Conduct an inspection of the drain hose.
• Fill the sink to which the dishwasher is attached with water.
• Clean the tub’s drain, filter, and sump.

Samsung Dishwasher Error Code 9E Code

Error Code 9E Code error happens when the low-level sensor is detected for more than 5 seconds during the wash cycle.

Drain and refill the water if the high-level sensor is not detected after the water delivery has been completed. This error happens if the high-level sensor is not detected again.

9E is one of the most frequently encountered problems with Samsung dishwashers. It is a sign of a decrease in water pressure.

Most likely, a malfunctioning water valve, damaged electronic components, or a twisted or obstructed water supply hose are to blame.

Additionally, the error occurs when the sensor located on the dishwasher’s side becomes blocked.

As a result, it is recommended to inspect the sensor and hoses on a regular basis and to remove food waste as needed.

If there is no waste or debris, it is likely that the sensor has failed and needs to be replaced.

The technique requires some skills, but if you are familiar with this type of dishwasher, you may complete it on your own.

How do I clear the 9E error code (Low water level error) on my Samsung dishwasher?

9E Error code is a Low water level error that indicated that there is not enough water in the Dishwasher.

To resolve this error, you need to;

• Empty the dishwasher.
• Add detergent, and then run a normal cycle.

If the error still occurs, switch off power to the dishwasher at the circuit breaker.

Samsung Dishwasher Error Code 7E

The error code e7 indicates that the waterwall reflector is defective. The fault code appears on the digital display of your Samsung Dishwasher to indicate that the waterwall reflector is unable to move.

This could be caused by something impeding the reflector’s movement or by an improperly fitted reflector.

How do I fix my Samsung dishwasher error code 7e?

Error Code 7E indicates that the water dispersion mechanism is immovable, with the a single-blade sprayer, rail, sensor, and electric motor.

To fix error code 7E, follow the following steps;

• Verify that the waterwall reflector is not obstructed. While you’re at it, double-check that nothing is blocking the reflector. If you newly installed the dishwasher, you must remove the packing tape.
• Inspect the location of the waterwall reflector. A waterwall reflector that is properly positioned will have its branding facing upward and forward.
• Repair a waterwall reflector that was improperly installed. Please remove it by raising it up from the vane. Adjust it appropriately and secure it securely on the gray shuttle’s waterwall rail.
• If your dishwasher’s reflector is properly placed but the error code continues, you must turn off the dishwasher’s electricity for two minutes.

Another possible explanation for the 7E Error is that one of the elements is still taped together, and you must locate and “unpack” it.

And, on the contrary, it could be caused by the sprinkler’s movement, which is now appropriately adjusted. If this is your situation, you can hear the strange sounds while executing a test program.

A malfunctioning electric engine is another probable cause of the 7E code appearing on your Samsung device’s display.

To inspect it, you must remove it from the machine, which is accomplished by opening the door and removing the bottom bar. Test it with the multimeter and, if necessary, replace it with a new one.

When resolving error code 7e on a Samsung dishwasher, you must check that you are resolving the correct error code. Utilize this guide to resolve the issue.

If the problem persists, contact a trained appliance technician for assistance.

Samsung Dishwasher Error Code 6E or BE (Button error)

What does Samsung Dishwasher 6E error Code mean?

Code error 6E/BE means that the dishwasher detects a stuck button or one of the touch buttons has been held for longer than 30 seconds

If the machine issues the 6E/BE error code, perhaps there is an insufficient contact of the buttons or their sticking after pressing. Try holding the key for about a minute or press it a few times. The fastening of the front panel of the washing machine also helps.

How do I clear the error code bE, 6E on my Samsung dishwasher?

The error code bE, 6E is a Button error and means that the panel detects a stuck button. To resolve or to clear the error, follow the following steps;

Turn off the dishwasher then inspect by touching every button on the panel if any buttons are not working correctly, or the error code returns after turning the dishwasher back on

Samsung Dishwasher Error Code CE (Communication Error)

CE-Communications Errors occur when communication between the machine controller and the motor controller is disrupted.

Several common causes of CE (Communications Error) include the following:

• Conformal coating applied to the serial communications pins connecting the machine controller and motor controller. After turning off the machine, attempt scraping the coating off the pins.
• With the connectors in place, measure the resistance between the serial communications pins. Ascertain that the harness does not contain any loose connections.
• Conduct a visual inspection of the quick disconnect at the motor terminal. A CE error will occur if the drive motor is not connected properly.
• The thermal protection for the drive motor has been opened.
• The motor controller is either not powered on or the fuse has blown. Change the motor controller.

How to fix Error Code CE

As mentioned, error code CE is a communication error and it indicated that the control panel is unable to communicate with the rest of the dishwasher.

To fix the CE error, turn off the dishwasher and try to start it again. If the error continues.

Samsung Washing Machine Error Code HE1

The error code HE1 (HE, HE2, HE3, HR) displayed on the washing machine’s display indicates a heating element problem. The absence of any notification of this error when washing in cold water on any program is direct evidence of this.

When the temperature is set to 40 degrees or higher, this error message shows on the display and the software ceases to operate.

Unfortunately, the owner cannot resolve the heating element issue on his or her own. As a result, if you detect one of the issues listed above, you will need to contact a service technician to get it repaired.

How to resolve the HE1 error code in a Samsung washing machine?

HE1 or HE2 relates to a Heater Error. Please turn off the washing dryer and wait approximately five minutes for it to calm down before restarting and checking. If the problem persists, please contact Samsung Customer Care in your country of residence.

Samsung Washing Machine Error Code HC, 1E, IE (Rotary Models)

Error codes HC, 1E, IE in Rotary Models indicated high temperature heater error and the temperature inside the dishwasher is too hot.

To fix this error,

• Switch the power to the dishwasher off (30 seconds) and then on again, at the circuit breaker.
• Empty the dishwasher.
• Fill the detergent drawer, and then start a normal cycle.

Samsung Dishwasher Error Code OC

What does OC Error Code stand for on a Samsung washing machine?

Samsung washing machine OC error code is a water level sensor error indicates that the drum has been overfilled with water.

The water level sensor transmits a signal indicating that the drum contains an excessive amount of water – more than the amount required for the set program.

Over-level water error can also be indicated by 0C & OE meaning the dishwasher has more water than it should. This is frequently a direct result of a drain issue.

How do I fix the OC error on my Samsung dishwasher?

• To begin, inspect the drain connection on the dishwasher at the sink.
• Conduct an inspection of the drain hose.
• Fill the sink to which the dishwasher is attached with water.
• Clean the tub’s drain, filter, and sump.

Samsung Washing Machine Error Code tE

The error code tE indicates the temperature sensor error and the temperature inside the dishwasher is being detected incorrectly.

To fix this error,

• Switch the power to the dishwasher off (30 seconds) and then on again, at the circuit breaker.
• Empty the dishwasher.
• Fill the detergent drawer, and then start a normal cycle.

If the error still occurs, switch off power to the dishwasher at the circuit breaker

Samsung Dishwasher Error Code PE

The error code PE indicates the Half load function error and the half load function is not performing correctly.

To fix this error,

• switch the power to the dishwasher off (30 seconds) and then on again, at the circuit breaker.
• Empty the dishwasher.
• Fill the detergent drawer, and then start a normal cycle.

If the error still occurs, switch off power to the dishwasher at the circuit breaker

Samsung Dishwasher Error Code PC

The error code PC indicates the Zone Wash error and the Zone Wash function is not operating correctly.

To fix this error, turn off the dishwasher and then try to start the cycle again.